BLJLP - R 0097 TT-P-26C INTERIOR PAINT

  • MSDS: BLJLP
  • Manufacturer: OCEAN COATINGS INC
  • Product Name: R 0097 TT-P-26C INTERIOR PAINT
  • National Stock Number: 8010-00-985-7017
Product Identification

Product ID:R 0097 TT-P-26C INTERIOR PAINT
MSDS Date:11/15/1989
FSC:8010
NIIN:00-985-7017
MSDS Number: BLJLP

Responsible Party
OCEAN COATINGS, INC.
BIRMINGHAM, AL 35201-0245
US

Emergency Phone: 800-462-0800

Info Phone: 205-324-9588

Cage: OCEAN

Contractor
OCEAN COATINGS, INC.
245 SAVANNAH, GA 31402 US

Telephone: (912) 234-1236

Cage: OCEAN

Ingredients

AROMATIC SOLVENT 100 (VP 2.7 MMHG @ 20C)

CAS: 64742-95-6

Fraction By Weight: <5.0%


2-BUTOXYETHANOL

CAS: 111-76-2

RTECS: KJ8575000

Fraction By Weight: <5.0%

OSHA PEL S, 50 PPM

ACGIH TLV: S, 25 PPM; 9293


PM ACETATE (VP 3.8 MMHG @ 25C)

CAS: 108-65-6

RTECS: AI8925000

Fraction By Weight: <5.0%


STODDARD SOLVENT

CAS: 8052-41-3

RTECS: WJ8925000

Fraction By Weight: 20%

OSHA PEL 500 PPM

ACGIH TLV: 100 PPM; 9293


PIGMENT(NOT A DUST HAZARD IN WET PAINT)

Fraction By Weight: 10%

Hazards

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Health Hazards Acute and Chronic:INHALATION: ANESTHETIC. IRRITATION OF
THE RESPIRATORY TRACT OR ACUTE NERVOUS SYSTEM DEPRESSION
CHARACTERIZED BY THE FOLLOWING PROGRESSIVE STEPS: HEADACHE,
DIZZINESS, STAGGERING GAIT, CONFUSION, UNCONS CIOUSNESS OR COMA.
Effects of Overexposure:INHALATION: IRRITATION OF THE RESPIRATORY
TRACT, HEADACHE, DIZZINESS, STAGGERING GAIT, CONFUSION,
UNCONSCIOUSNESS OR COMA. SKIN OR EYE CONTACT: PRIMARY IRRITATION &
SENSITIZER.
Medical Cond Aggravated by Exposure:SEE YOUR PHYSICIAN FOR DEFINITIVE
MEDICAL ADVICE CONCERNING YOUR CONDITION.

First Aid

First Aid:FUMES: REMOVE FROM EXPOSURE. RESTORE BREATHING. KEEP WARM &
QUIET. NOTIFY A PHYSICIAN. SPLASH(EYES): FLUSH IMMEDIATELY WITH
RUNNING WATER FOR 15 MINUTES. TAKE TO A PHYSICIAN FOR MEDICAL
TREATMENT. SPL ASH(SKIN): WASH AFFECTED AREA WITH SOAP& WATER.
REMOVE CONTAMINATED CLOTHING & LAUNDER BEFORE REUSE. CONSULT A
PHYSICIAN.

Fire Fighting

Flash Point:100F,38C
Lower Limits:1.0
Extinguishing Media:FOAM, CO2, DRY CHEMICAL, WATER FOG, OTHER.
Fire Fighting Procedures:WATER MAY BE USED TO COOL CLOSED CONTAINERS TO
PREVENT PRESSURE BUILD-UP, AUTOIGNITION OR EXPLOSION WHEN EXPOSED
TO EXTREME HEAT. KEEP CONTAINER TIGHTLY CLOSED.
Unusual Fire/Explosion Hazard:ISOLATE FROM HEAT, ELECTRICAL EQUIP,
SPARKS & OPEN FLAME. CLOSED CONTAINERS MAY EXPLODE FROM EXTREME
HEAT. DO NOT APPLY TO HOT SURFACES. FOG NOZZLES PREFERABLE.

Accidental Release

Spill Release Procedures:REMOVE ALL SOURCES OF IGNITION(FLAMES, HOT
SURFACES & ELECTRICAL, FRICTIONAL OR STATIC SPARKS.) AVOID
BREATHING VAPORS. REMOVE WITH NON-SPARKING TOOLS.

Handling

Handling and Storage Precautions:DO NOT STORE ABOVE 120 F. STORE LARGE
QUANTITIES IN BUILDINGS DESIGNED & PROTECTED FOR STORAGE OF NFPA
CLASS II FLAMMABLE LIQUIDS.
Other Precautions:DO NOT TAKE INTERNALLY. CONTAINERS SHOULD BE GROUNDED
WHEN POURING. AVOID FREE FALL OF LIQUIDS IN EXCESS OF A FEW INCHES.
NEVER FLAME CUT, BRAZE OR WELD DRIED FILM WITHOUT NIOSH APPROVED
RESPIRATOR OR APPROPRIATE VENTILATION.

Exposure Controls

Respiratory Protection:OUTDOOR/OPEN AREAS:USE NIOSH APPROVED MECHANICAL
FILTER RSPRTR TO REMOVE SOLID AIRBORNE PARTICLES WHEN SPRAYING.
RESTRICTED VENT:USE CHEM-MECHANICAL FILTER TO REMOVE COMBINATION OF
PARTICULATE, GAS & VAPOR. CONFINED:AIR LINE RSPRTR OR HOODS
Ventilation:PROVIDE GENERAL DILUTION OR LOCAL EXHAUST VENTILATION IN
VOLUME & PATTERN TO KEEP TLV & LEL BELOW STATED LIMITS.
Protective Gloves:REQUIRED FOR PROLONGED/REPEATED CONTACT
Eye Protection:SAFETY EYEWARE TO PROTECT AGAINST SPLASH
Other Protective Equipment:AVOID PROLONGED BREATHING OF VAPOR OR SPRAY
MIST OR PROLONGED SKIN CONTACT TO CONTAMINATED CLOTHING.
Work Hygienic Practices:WASH WITH SOAP & WATER BEFORE EATING, DRINKING,
SMOKING OR USING TOILET.
Supplemental Safety and Health

Chemical Properties

Boiling Pt:B.P. Text:244 TO 388F
Vapor Density:> THAN AIR
Evaporation Rate & Reference:SLOWER THAN ETHER
Percent Volatiles by Volume:45.11

Stability

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZERS
Stability Condition to Avoid:POSSIBLE COMBUSTION CONDITIONS.
Hazardous Decomposition Products:CARBON MONOXIDE, FUMES, SMOKE AND
GASES FROM THERMAL DECOMPOSITION.
Conditions to Avoid Polymerization:WILL NOT OCCUR

Disposal

Waste Disposal Methods:PICK-UP WITH INERT ABSORBENT. DISPOSE IN
ACCORDANCE WITH LOCAL, STATE & FEDERAL REGULATIONS. INCINERATE IN
APPROVED FACILITY. DO NOT INCINERATE CLOSED CONTAINERS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.